LPC1752FBD80|Arm Cortex-M3|32-bit MCU

For best experience this site requires Javascript to be enabled. To enable on your browser, follow our accessibility instructions.

The LPC1752 is a Cortex-M3 microcontroller for embedded applications featuring a high level of integration and low power consumption at frequencies of 100 MHz. Features include 64 kB of flash memory, 16 kB of data memory, USB Device, 8-channel DMA controller, 4 UARTs, 1 CAN channels, 2 SSP, 1 SPI, 2 I2C, 8-channel 12-bit ADC, motor control PWM, Quadrature Encoder interface, 4 general purpose timers, 6-output general purpose PWM, ultra-low power Real-Time Clock with separate battery supply, and up to 52 general purpose I/O pins.

See product image

Data Sheet

Application Notes

Product Details

Block Diagram

Block diagram: LPC1751FBD80, LPC1752FBD80, LPC1754FBD80, LPC1756FBD80, LPC1758FBD80

Get diagram PDF

Features

Arm Cortex-M3 processor, running at frequencies of up to 100 MHz
Arm Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC)
Up to 64 kB on-chip flash programming memory
Up to 16 kB of SRAM
In-System Programming (ISP) and In-Application Programming (IAP)
Eight channel General Purpose DMA controller (GPDMA)
Multilayer AHB matrix interconnect provides a separate bus for each AHB leader
Split APB bus allows high throughput with few stalls between the CPU and DMA
USB 2.0 full-speed device controller
Four UARTs with fractional baud rate generation
CAN 2.0B controller with one channel
SPI controller with synchronous, serial, full duplex communication
Two SSP controllers with FIFO and multi-protocol capabilities
Two I2C-bus interfaces supporting fast mode with a data rate of 400 kbit/s
52 General Purpose I/O (GPIO) pins with configurable pull-up/down resistors
12-bit Analog-to-Digital Converter (ADC) with conversion rates up to 200 kHz
Four general purpose timers/counters
One motor control PWM with support for three-phase motor control
Quadrature encoder interface that can monitor one external quadrature encoder
One standard PWM/timer block with external count input
Real-Time Clock (RTC)
WatchDog Timer (WDT)
Arm Cortex-M3 system tick timer, including an external clock input option
Standard JTAG test/debug interface. Boundary scan Description Language (BSDL) is not available for this device
Integrated PMU (Power Management Unit)
Four reduced power modes
Single 3.3 V power supply (2.4 V to 3.6 V)
One external interrupt input configurable as edge/level sensitive
Non-maskable Interrupt (NMI) input
Wakeup Interrupt Controller (WIC)
Processor wake-up from Power-down mode via any interrupt
Brownout detect with separate threshold for interrupt and forced reset
Power-On Reset (POR)
Crystal oscillator with an operating range of 1 MHz to 25 MHz
4 MHz internal RC oscillator trimmed to 1 % accuracy
PLL allows CPU operation up to the maximum CPU rate
USB PLL for added flexibility
Code Read Protection (CRP) with different security levels
Unique device serial number for identification purposes

Target Applications

eMetering
Lighting
Industrial networking
Alarm systems
White goods
Motor control

Buy/Parametrics

‌ ‌ ‌	‌ ‌	‌ ‌	‌ ‌	‌ ‌	‌ ‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌

Design Resources

Design Files

Quick reference to our design files types.

2 design files

Receive the full breakdown. See the product footprint and more in the eCad file.

Models
BSDL for LPC175x and LPC176x

ZIPRev 1Jun 13, 2017 11:57:00236 BBSDL_LPC175X_6X
DownloadToggle Dropdown
- Add to Queue
- Remove from Queue
- Recommended for large file sizes.
- View Queue
Symbols and Footprints
LPC175x/6x ORCAD symbols

ZIPRev 0Jun 3, 2016 00:00:0025.6 KBLPC175X-LPC176X-ORCAD-SYM

Account Required
DownloadToggle Dropdown
- Add to Queue
- Remove from Queue
- Recommended for large file sizes.
- View Queue

Hardware

Quick reference to our board types.

1-5 of 8 hardware offerings

Emulators, Probes, and Programmers
Universal Multilink Development Interface
Active

UMultilink
Emulators, Probes, and Programmers
PEmicro Cyclone FX programmer

CYCLONE-FX
Emulators, Probes, and Programmers
MCU-Link Debug Probe
Active

MCU-LINK
Emulators, Probes, and Programmers
LPC-Link2
Active

OM13054
Emulators, Probes, and Programmers
MCU-Link Pro Debug Probe
Active

MCU-LINK-PRO
Emulators, Probes, and Programmers
Universal Multilink FX High-Speed Development Interface
Active

U-MULTILINK-FX
Emulators, Probes, and Programmers
PEmicro Cyclone programmer
Active

CYCLONE
Evaluation and Development Boards
LPCXpresso board for LPC1769 with CMSIS DAP probe
Active

OM13085

Show All

Engineering Services

To get further assistance directly from NXP, please see our Engineering Services.

3 engineering services

Independent Design House (IDH)
Debug Tool development

By Ashling Microsystems GoldHQ: Limerick, IrelandSupporting Regions: EMEA
Independent Design House (IDH)
Wireless and Antenna Design

By Bluewind GoldHQ: Castelfranco Veneto, ItalySupporting Regions: EMEA
Independent Design House (IDH)
IDE development

By Ashling Microsystems GoldHQ: Limerick, IrelandSupporting Regions: EMEA

To find additional partner offerings that support this product, visit our Partner Marketplace.

Training

9 trainings

On-Demand
CANopen

2By port industrial automation GmbH Gold Partner

On-Demand
Advanced wolfSSL for Embedded Security

12 hrBy AC6-Training Gold Partner

On-Demand
Developing with Arm Cortex-M

35 hrBy Doulos Ltd Gold Partner

On-Demand
wolfSSL for Embedded Security

18 hrBy AC6-Training Gold Partner

On-Demand
C++ Programming for Embedded Systems ONLINE

30 hrBy Doulos Ltd Gold Partner

On-Demand
Advanced Embedded Systems Security

12 hrBy AC6-Training Gold Partner

On-Demand
C Programming for Embedded Systems ONLINE

30 hrBy Doulos Ltd Gold Partner

On-Demand
Writing Secure C/C++ code

18 hrBy AC6-Training Gold Partner

On-Demand
Embedded System Security for C/C++ Developers ONLINE

24 hrBy Doulos Ltd Gold Partner

Show All

Scalable Mainstream 32-bit Microcontroller (MCU) based on Arm® Cortex®-M3 Core

Product Details

Block Diagram

Block diagram: LPC1751FBD80, LPC1752FBD80, LPC1754FBD80, LPC1756FBD80, LPC1758FBD80

Features

Target Applications

Applications

Automotive

Consumer

Industrial

Buy/Parametrics

Documentation

Filter by

Application Note (25)

Connecting TFT LCD with LCD controller of LPC MCU[AN12027]

AES encryption and decryption software on LPC microcontrollers[AN11241]

Guidelines for full-speed USB on NXP's LPC microcontrollers[AN11392]

Capacitive touch sensing using the LPC176x/5x[AN11095]

Using Speex in NXP's LPC175x/6x MCU family[AN11085]

Memory to DAC data transfers using the LPC1700's DMA[AN10917]

Accessing SDC/MMC card using SPI/SSP on LPC1700[AN11070]

Decoding DTMF tones using M3 DSP library FFT function[AN10943]

In-Application Programming for the LPC1700[AN11071]

FAT library EFSL and FatFs port on NXP LPC1700[AN10916]

MP3 player solution on NXP LPC1700 series[AN11178]

I2C secondary boot loader[AN11258]

How to implement the PMBus software stack[AN11318]

LPC1700 secondary USB bootloader[AN10866]

SPI secondary boot loader[AN11257]

BLDC motor control with LPC1700[AN10898]

LPC176x/175x 12-bit ADC design guidelines[AN10974_ZH]

UUencoding for UART ISP[AN11229]

DSP library for LPC1700 and LPC1300[AN10913_CM3_DSP_LIBRARY_V1_0_0]

PCB layout guidelines for NXP® MCUs in BGA packages[AN10778]

AN10974 - LPC176x/175x 12-bit ADC design guidelines[AN10974_-_LPC176X_175X_12-BIT_]

LPC176x/175x 12-bit ADC design guidelines[AN10974]

DSP library for LPC1700 and LPC1300[AN10913]

Using M3 DSP library filter functions[AN10934]

Migrating to the LPC1700 series[AN10878]

Brochure (2)

Cortex-M3 based microcontrollers with Ethernet, USB, CAN and 12-bit ADC; 120 MHz, 32-bit Microcontrollers with Cortex-M3™ core, LPC1700 series[75016846]

Cortex-M3 based microcontrollers with Ethernet, USB, CAN and 12-bit ADC; 100 MHz, 32-bit Microcontrollers with Cortex-M3™ core, LPC1700 series[75016676]

Data Sheet (1)

32-bit ARM Cortex-M3 MCU; up to 512 kB flash and 64 kB SRAM with Ethernet, USB 2.0 Host/Device/OTG, CAN[LPC1759_58_56_54_52_51]

Errata (1)

Errata sheet LPC1759/58/56/54/52/51[ES_LPC175X]

Package Information (1)

plastic low profile quad flat package; 80 leads; body 12 x 12 x 1.4 mm[SOT315-1]

Supporting Information (2)

ADC design guidelines[TN00009]

Footprint for wave soldering[HTQFP-HLQFP-LQFP-MSQFP-WAVE]

Training Presentation (1)

Driving LPC1700/LPC1800/LPC4300 with EPSON Crystals[R_10076]

User Guide (1)

LPC176x/5x User manual[UM10360]

Design Resources

Design Files

Filter by

BSDL for LPC175x and LPC176x

LPC175x/6x ORCAD symbols

Filter By

Hardware

Filter By

Filter By

Software

Filter by

AN10859 - LPC1700 Ethernet MII Management (MDIO) via software

Filter By

Engineering Services

Filter by

Training

Filter by

Scalable Mainstream 32-bit Microcontroller (MCU) based on Arm^® Cortex^®-M3 Core

PCB layout guidelines for NXP^® MCUs in BGA packages[AN10778]